MIMAKI JV5-320S Spezifikationen

COLOR INKJET PRINTEROPERATION MANUALMIMAKI ENGINEERING CO., LTD.TKB Gotenyama Building, 5-9-41, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, JapanPhon

viiiCHAPTER 4Daily CareRoutine Maintenance ...4-2Precautions in clea

3 Printing3-283 Adjust the position of the left roll holder.Loosen the roll holder securing screw on the left, and insert the left roll holder into th

3-29Setting the media on the printer5 Pull out the media to the front, and put the start of the media on the paper core with tape.1.Holding the center

3 Printing3-308 Close the front cover and press the [ENTER] key.The printer performs initial operation and displays the standby state.

3-31Setting the media on the printer When the media thickness cannot be detectedThere may be a case where the media thickness cannot be detected prope

3 Printing3-32When [MEDIA RESIDUAL] of [MAINTENANCE] function has been set to ONSTEPS:1 Detection is completed, and the carriage returns to the statio

3-33Setting the media on the printerHow to operate the take-up deviceThe take-up device is equipped with a switch that selects the direction in which

3 Printing3-34Setting cut sheet media on the printerUnlike roll media, cut sheet media need not be retained with the roll holders.STEPS:1 Open the fro

3-35Setting the media on the printer3 Hold the media with the media press lightly, not to be lifted the media.4 Push down the clamp lever and close th

3 Printing3-366 Press the [] key and select [LEAF].After detecting the media, the printer returns to LOCAL mode. (Refer to “LOCAL mode (p.2-22)” )

3-37Selecting and checking printing conditionsSelecting and checking printing conditionsWhen the Type 1 to Type 4 printing conditions have already bee

ixCHAPTER 5In Case of TroubleBefore taking a phenomenon as a failure ...5-2Power does not turn on...

3 Printing3-38Operating the heatersWhen shipped from the plant, all heaters are set to OFF.Switch the heater ON and set the temperature as required.Tu

3-39Operating the heatersChecking the preset temperature and setting a temperature during printingThis section describes how to adjust the heater temp

3 Printing3-40What is beading ?Beading is a phenomenon that adjacent dots attracts each other and join. Beading causes speckled patterns or stripes al

3-41Operating the heatersTemperature adjustment This section describes the procedure for setting the heater temperatures properly. The proper heater t

3 Printing3-42In case of heater troubleWhen the Power Switch of the heaters is turned off, or if heaters have developed problem, the display turns as

3-43Setting the reference value for dot misalignment correction [PG DROP ADJUST.]Setting the reference value for dot misalignment correction [PG DROP

3 Printing3-445 Press the [] or [] key to correct the dot position of pattern 1.Select the correct dot position on [PATTERN 1] using the JOG key [

3-45Checking for nozzle clogging, and unclogging nozzlesChecking for nozzle clogging, and unclogging nozzlesPrint a test pattern and check to see if t

3 Printing3-46Relationship between head row and test patternThe relations between head row and test pattern print position are as follow.If the printe

3-47Checking for nozzle clogging, and unclogging nozzles4 Select a cleaning method using the [] or [] key.5 Press the [ENTER] key.Cleaning starts.Th

xInvoking MACHINE SETUP functions...6-18List of functions ...

3 Printing3-48If nozzles cannot be unclogged [FILL UP INK]Execute the [FILL UP INK] function when the blocked nozzles are not unclogged even by execut

3-49Checking for nozzle clogging, and unclogging nozzles4 Press the [ENTER] key.Ink filling is started automatically.On completion of ink filling, the

3 Printing3-50Correcting the media feed rate [MEDIA COMP.]The media feed rate changes when the media type or any heater temperature is changed, or dep

3-51Correcting the media feed rate [MEDIA COMP.]3 By judging from the output pattern, enter a correction value using the [] or [] key.4 Press the [E

3 Printing3-52If dots are not in alignment [DROP.POScorrect]Dots may be slightly out of alignment even after [PG DROP ADJUST.] is made. In this case,

3-53If dots are not in alignment [DROP.POScorrect]5 Press the [] or [] key to correct the dot position of pattern 1.Select the correct dot position

3 Printing3-54Effective Plotting AreaThe printer has an area where printing is not permitted, for mechanical reasons.This area is called “non-printing

3-55Establishing the OriginEstablishing the OriginEstablish the origin for printing the data on the media loaded on the printer.When printing requires

3 Printing3-56Typical setting position of printing originThe printing origin in the depth direction (X’) is positioned at about 140 mm rearward from t

3-57Printing an imagePrinting an imageStarting the printing operationThe following describes mode switching for receiving data from the computer and i

Checking the accessories ...1-2Features ...

3 Printing3-58STEPS:1 Check the heater temperatures.Make sure that the CONSTANT lamps on the heater panel are lit. (See 3-39)2 Press the [REMOTE] key.

3-59Printing an imageCutting the media after completion of printingAfter completion of printing, cut the media at any desired position without using t

3 Printing3-603 Press the [ENTER] key.The printer cuts the media.4 The printer returns to LOCAL mode.The printer restores the same status as before en

3-61Printing an imageWhen [] key is allocated to Direct Cut Key in [MEDIA CUT] of [MACHINE SET] function.STEPS:1 Make sure that the printer is in LOC

3 Printing3-62Automatic cleaningSetting can be made to select whether or not to clean the heads automatically during printing.Reliable output results

3-63Printing an image4 Press the [FUNCTION] key.5 At this point, either of [CLEANING INTERVAL] and [CLEANING TYPE] can be selected by pressing the []

3 Printing3-64Maintenance while Printing (When dedicated sublimation transfer ink (Sb51) is used)The auto cleaning or auto wiping while printing will

3-65Printing an image4 Press the [FUNCTION] key.5 At this point, either of [CLEANING INTERVAL] and [CLEANING TYPE] can be selected by pressing the []

3 Printing3-66When setting to WIPING.STEPS:1 Make sure that the printer is in LOCAL mode.If it is in REMOTE mode, press the [REMOTE] key.2 Select [SET

3-67Display of [INK NEAR END] or [INK END]Display of [INK NEAR END] or [INK END]A message appears when one of the two ink cartridges in a set is compl

1 Safety Precautions1-2Checking the accessoriesThe articles illustrated below are supplied with your printer as accessories.Check them for correct qua

3 Printing3-68STEPS FOR REPLACEMENT1 A message [INK NEAR END] or [INK END] appears during printing.Once [INK NEAR END] appears, the printer returns to

3-69Display of [INK NEAR END] or [INK END]Display ink informationThe remaining amount of ink can be checked.STEPS:1 Press the [ENTER] key while the pr

3 Printing3-70Turning the power offAfter completing all desired operations with the printer, press the power switch on the front of the printer to tur

Routine Maintenance ...4-2Cleaning the wiper and ink caps [CARRIAGE OUT] ...4-7C

4 Daily Maintenance4-2Routine MaintenanceBe sure to perform maintenance of the printer periodically or whenever necessary so that the printer can be u

4-3Routine MaintenanceNotes on cleaning solutionUse the cleaning liquid dedicated for the ink being used.Cleaning exterior surfacesIf exterior surface

4 Daily Maintenance4-4Cleaning the media sensor (2 places)Using a cotton swab, clean the surface of the sensor of dust and dirt.Cleaning the media pre

4-5Routine MaintenanceOpening the maintenance coverRemove a maintenance cover to clean the inside of the printer. It is necessary to remove the approp

4 Daily Maintenance4-6STEPS:1 Remove the top two screws for the maintenance cover.2 With the shaft of the frame as the fulcrum, turn over the maintena

4-7Cleaning the wiper and ink caps [CARRIAGE OUT]Cleaning the wiper and ink caps [CARRIAGE OUT]The ink caps prevent the nozzles in the heads from dryi

1-3Checking the accessoriesRoll Paper : 1 each for 160 / 320 wideSolvent pre-fill up solu-tion cartridge (200 cc) : 8Accessories Box : 1Cleaning S

4 Daily Maintenance4-83 Open the right maintenance cover.4 Pull out the wiper by holding the projections at both ends.5 Remove the ink from the wiper

4-9Cleaning the wiper and ink caps [CARRIAGE OUT]6 After cleaning the wiper, install it in position by holding the projections at both ends.Be careful

4 Daily Maintenance4-10Cleaning the nozzle [NOZZLE WASH]Perform cleaning of the nozzles in the heads to prevent them being clogged with coagulated ink

4-11Cleaning the nozzle [NOZZLE WASH]4 Pull out the wiper by holding the projections at both ends.5 Remove the ink from the wiper, bracket and the vic

4 Daily Maintenance4-128 Fill the caps with the cleaning solution using a dropper.9 Close the maintenance cover and press the [ENTER] key.10Set the ti

4-13Cleaning the ink discharge passage [DISWAY WASH]Cleaning the ink discharge passage [DISWAY WASH]Use this function when the [PUMP TUBE WASH] functi

4 Daily Maintenance4-143 Open the right maintenance cover.4 Take the cleaning solution into the dropper.During a pause of idle suction, drop cleaning

4-15When the operation of the printer is to be suspended for a long time [CUSTODY WASH]When the operation of the printer is to be suspended for a long

4 Daily Maintenance4-164 Pull out the wiper by holding the projections at both ends.5 Remove the ink from the wiper and the bracket using a cotton swa

4-17When the operation of the printer is to be suspended for a long time [CUSTODY WASH]8 Fill the caps with the cleaning solution using a dropper.9 Cl

1 Safety Precautions1-4FeaturesThe features of the printer are described below.Understanding them together with the operating instructions given in th

4 Daily Maintenance4-1812Open the maintenance cover, and fill the caps with the cleaning solution using a dropper.Since the printer performs idle suct

4-19Before executing the [PUMP TUBE WASH]Before executing the [PUMP TUBE WASH]Before executing the [PUMP TUBE WASH] or [Wiper cleaning] function, the

4 Daily Maintenance4-205 Press the [ENTER] key to go to the lower level of hierarchy and supply the cleaning solution.Once the cartridge is installed,

4-21Before executing the [PUMP TUBE WASH]Supply after discharge9 Set a cleaning liquid cartridge according to the instruction on the display.10The cle

4 Daily Maintenance4-22PUMP tube cleaningWash the two ink suction pumps of the four pumps installed in this printer.By driving the cleaning liquid suc

4-23PUMP tube cleaning3 The inside of the pump tubes is washed.WASHINGPLEASE WAITPUMP TUBE WASH00:30WASHINGPLEASE WAITPUMP TUBE WASH∗ ∗ ∗ ∗ ∗ ∗ ∗ − −

4 Daily Maintenance4-24Wiper cleaningBring the wiper into the wiper box and wash the wiper.Washing will not be started if the cleaning liquid has not

4-25Wiper cleaning5 Pull out the wiper by holding the projections at both ends.6 Remove the ink from the wiper and the bracket using a cotton swab dam

4 Daily Maintenance4-26Cleaning the heads and their surrounding parts[CR.MAINTENANCE]Take great care, especially during cleaning, not to damage the he

4-27Cleaning the heads and their surrounding parts [CR.MAINTENANCE]5 Wipe ink and dirt off the head sides using a cotton swab.6 Clean the head media s

1-5FeaturesIndication of the INK RemainsSince the amount of ink that remains can be checked even during operation of the printer, you can use the ink

4 Daily Maintenance4-28Preventing nozzle clogging while power is off [SLEEP SET UP]Even while the power switch is off, the printer starts periodically

4-29Preventing nozzle clogging while power is off [SLEEP SET UP]Tube cleaning interval during sleep mode [TUBE WASH]Set the interval at which cleaning

4 Daily Maintenance4-30Cleaning interval during sleep mode [CLEANING]This function is to be executed instead of TUBE WASH after the cleaning solution

4-31Setting periodical operations in stand-by mode [ROUTINE SETUP]Setting periodical operations in stand-by mode [ROUTINE SETUP]While the printer is w

4 Daily Maintenance4-324 Input the value of SCAN COUNT using the [] or [] key.Register the setting by pressing the [ENTER] key.5 Press the [] key t

4-33Setting periodical operations in stand-by mode [ROUTINE SETUP]Refresh Interval while in stand-by mode [REFERSH]Set the interval at which refreshin

4 Daily Maintenance4-34Tube cleaning interval while in stand-by mode [TUBE WASH]There may be a chance that ink tubes can be clogged with coagulated in

4-35Setting periodical operations in stand-by mode [ROUTINE SETUP]Cleaning interval while in stand-by mode [CLEANING]This function is to be executed i

4 Daily Maintenance4-364 Select the interval at which cleaning is to be performed periodically, using the [] or [] key.Select [CLEAN. TYPE] using th

4-37Other maintenance functionsOther maintenance functionsChanging warning time of wiper replacement [WIPER LEVEL]The wiper is consumable. The heads a

1 Safety Precautions1-6The nozzle missing automatic detection function reduces waste of media and ink that could be caused by faulty printingThe print

4 Daily Maintenance4-383 Input the WIPER LEVEL, using the [] or [] key.Register the setting by pressing the [ENTER] key.4 Press the [END] key severa

4-39Other maintenance functionsChanging warning time of flushing BOX cleaning or replacement [BOX EXCHANGE LV]Flushing BOX becomes tainted earlier tha

4 Daily Maintenance4-40When the waste ink tank is fullWaste ink, which was used for cleaning the heads and other parts, gathers in the waste ink tank.

4-41When the waste ink tank is full4 By holding the larger handle of the new waste ink tank, put the tank into the bracket from the right direction.5

4 Daily Maintenance4-42Cleaning of Flushing BoxWhen the following warning message appears, quickly clean the lid of the suction fan box.When the warni

4-43Cleaning of Flushing BoxSTEPS:1 Press the power switch on the front and make sure that the power is off.2 Turn off the main power switch on the si

4 Daily Maintenance4-444 Pull out the lid of the suction fan box.Remove the grip fixing the suction fan box and then pull out the lid of the box.5 Rem

4-45Cleaning of Flushing Box11Press the [END] key several times.The printer returns to LOCAL mode. When the printer is in local mode, if you press th

4 Daily Maintenance4-46Replacing the wiper [WIPER EXCHANGE]The wiper is consumable.When the display indicates that it is necessary to replace the wipe

4-47Replacing the wiper [WIPER EXCHANGE]4 Clean the wiper guide shaft using a cotton swab or cloth.If dirt is hard to remove, use a cotton swab dampen

1-7SymbolsSymbolsPictorial signs are used in this Operation Manual for safe operation and for prevention of damage to the printer. Pictorial signs and

4 Daily Maintenance4-48Replacing the cutter bladeThe cutter blade is consumable.When the cutter blade gets dull, replace it with a new one (SPA-0126).

4-49Replacing the cutter blade4 Loosen the screw securing the cutter unit and remove the cutter unit.5 Remove the roller, and install it on the new cu

4 Daily Maintenance4-50

Before taking a phenomenon as a failure ...5-2If image quality is poor ...

5 In Case of Trouble5-2Before taking a phenomenon as a failureThis section describes the corrective actions to be taken at the occurrence of trouble w

5-3Before taking a phenomenon as a failureMedia jamming arises / media is soiledMedia jamming or stained media is considered to be due to the use of a

5 In Case of Trouble5-4If image quality is poorThis section describes the corrective actions to be taken in case the image quality is not satisfactory

5-5If image quality is poorDisagreement in print positions between outward trip and homeward trip (jet deviation)RemedyExecute the [DROP.POScorrect] f

5 In Case of Trouble5-6If nozzles are still clogged even after head cleaningExecute the following two functions if blocked nozzles are not unclogged e

5-7If image quality is poor4 Remove the ink cartridges.Ink is discharged to the waste ink tank.5 When the display shown below appears, set the cleanin

ForewordCongratulations on your purchase of MIMAKI color ink jet printer “JV5-320S” .The JV5-320S is a color ink-jet printer for high quality printing

1 Safety Precautions1-8Notes on InstallationWhere to install the printerSecure a suitable installation space before assembling the printer.The place o

5 In Case of Trouble5-87 When the display shown below appears, set the cleaning liquid cartridge in the ink station.Cleaning liquid is drawn up.8 When

5-9If image quality is poor11When the display shown below appears, remove the cleaning liquid cartridge from the ink station.The cleaning liquid drawn

5 In Case of Trouble5-10When nozzle clogging is not corrected [HEAD SELECT]If nozzles cannot be unclogged, make setting so that the printer will not u

5-11If image quality is poorSTEPS:1 Make sure that the printer is in LOCAL mode, and then select [MAINTENANCE] using the [FUNCTION] key and press the

5 In Case of Trouble5-12Ink cartridge troubleIf an ink cartridge trouble is detected, a warning message appears and none of printing, cleaning and all

5-13Ink cartridge troubleIf ERROR 202 [DEVICE CONSTRUCTION] is displayedThis printer checks its configuration every time it starts.The configuration c

5 In Case of Trouble5-14Troubles for which error messages are displayedIf some trouble occurs, the buzzer sounds and the display shows a corresponding

5-15Troubles for which error messages are displayedWarning messagesWarning messages will appear chiefly to warn of the conditions of heaters or ink ca

5 In Case of Trouble5-16L.∗> !CAR [JV5-01]There is a problem with installed ink cartridges.(If this occurs together with any other warning, the di

5-17Troubles for which error messages are displayedExpiration:1MONTH- - - - - - - - - - - - - - - -The expiration date of an ink cartridge has pass

1-9Notes on InstallationNotes on LocationDo not locate the printer in any of the places listed below.Locking the casters and fixing the printer with l

5 In Case of Trouble5-18!Feeding CoverOPENThe cover of heavy-duty feeding device is detected open.Check the cover of heavy-duty feeding device.If the

5-19Troubles for which error messages are displayedError messagesError messages indicates error numbers.If any error message is displayed, turn off th

5 In Case of Trouble5-20∗∗∗∗∗ ERROR 16 ∗∗∗∗∗MRL COMMANDAn error occurred in the control sys-tem.Transmit data that is compatible with the command syst

5-21Troubles for which error messages are displayed∗∗∗∗∗ ERROR 30 ∗∗∗∗∗OPERATION ERRORImproper operation was conducted on the operation panel.The Disp

5 In Case of Trouble5-22∗∗∗∗∗ ERROR 58 ∗∗∗∗∗POSITION ENCODER:DIRAn error occurred in the control sys-tem.Turn off the power to the printer and turn it

5-23Troubles for which error messages are displayed∗∗∗∗ ERROR 122 ∗∗∗∗CONDENSATIONAs the ambient temperature is low, head condensation may occur.Raise

5 In Case of Trouble5-24∗∗∗∗ ERROR 160 ∗∗∗∗NCU DETECT 02An error occurred in the control sys-tem.Turn off the power to the printer and turn it on afte

5-25Troubles for which error messages are displayed∗∗∗∗ ERROR203 ∗∗∗∗SDRAM SIZEAn error occurred in the control sys-tem.Turn off the power to the prin

5 In Case of Trouble5-26

Functions Invoked by [FUNCTION] Key ...6-2Invoking SET UP functions ...

1 Safety Precautions1-10Moving the printerWhen the printer is to be moved by necessity, moving it is permitted only on the same floor where there is n

6 Operation for Functions6-2Functions Invoked by [FUNCTION] KeyThe following five types of functions can be invoked by pressing the [FUNCTION] key.Fun

6-3Invoking SET UP functionsInvoking SET UP functionsRegistering printing conditions in a lump (type registration)FUNCTION mode provides 17 setup func

6 Operation for Functions6-4Settings of the setup functionsThe operation described below on the operation panel is required to execute the setup funct

6-5Invoking SET UP functionsOutline of the setup functionsMEDIA COMP. (See 3-50)When the media type or any heater temperature is changed, be sure to c

6 Operation for Functions6-6PRINT MODESets various conditions of printing.DRAFT qualitySet a desired print quality in DRAFT mode (540 dpi resolution i

6-7Invoking SET UP functionsFINE qualitySet a desired print quality in FINE mode (720 dpi resolution in the Y-axis direction).Available setting values

6 Operation for Functions6-8LOGICAL SEEKSet LOGICALseek ON / OFF.Available setting values: [ON, OFF]Movement of heads when LOGICALseek is OFFMovement

6-9Invoking SET UP functionsAUTO CUTSet whether or not to cut the media automatically after completion of printing.Available setting values: [ON, OFF]

6 Operation for Functions6-10COLOR PATTERNSet whether or not to print a color pattern for nozzle missing check near the right edge of the media.Availa

6-11Invoking SET UP functionsREFRESHSet the head refreshing level (running flush interval).Available setting values: [0 ~ 3] ( Enhancing the level sho

1-11Connecting Power SupplyConnecting Power SupplyPrinter specificationsSingle-phase 200 to 240 Vac 30 A or less (cannot be used with 100 V system)For

6 Operation for Functions6-12AUTO CLEANING (See 3-62)Set whether or not to clean the heads automatically before printing.Available setting values: [ON

6-13Invoking SET UP functionsSETUP RESETReset the settings of the setup functions assigned to the user types 1 to 4 to the default values.

6 Operation for Functions6-14Invoking MAINTENANCE functionsThe maintenance functions described here are to be executed to keep the printer in good con

6-15Invoking MAINTENANCE functionsSetting a maintenance functionTake the following steps on the operation panel to execute a maintenance function.STEP

6 Operation for Functions6-16Make setting of the media remaining amount display function [MEDIA RESIDUAL]Set ON/OFF of the media remaining amount disp

6-17Invoking MAINTENANCE functionsMoving the printer safely [BeforeMovingIt.]Use this function to lock the station when the printer is to be moved.Use

6 Operation for Functions6-18Invoking MACHINE SETUP functionsList of functionsThis section describes briefly the machine setup functions and their set

6-19Invoking MACHINE SETUP functionsSetting a MACHINE SETUPThe operation described below on the operation panel is required to execute machine setup f

6 Operation for Functions6-20Outline of the machine setup functionsFeeding / TakeUPFor heavy-duty feeding / take-up device, set whether to use or not

6-21Invoking MACHINE SETUP functionsMEDIA CUTSet a key assignment for media cutting and the operation after cutting.ASSIGN CUT KEYSet whether to assig

1 Safety Precautions1-12Warning for Use WARNINGBe sure to install a ventilator, if necessary, to ensure good ventilation in the room where the printer

6 Operation for Functions6-22STAMP SETUPSet whether or not to output the printing conditions and the date and time of printing.With STAMP SETUP set to

6-23Invoking MACHINE SETUP functionsDetection of mediaThickness DetectionSet whether to perform automatically or manually the detection of media thick

6 Operation for Functions6-24PRT.modeHISTORYDisplays the information (printing conditions) of the online printing that has been performed up to now si

6-25Invoking MACHINE SETUP functionsWhen sublimation transfer ink Sb51 is usedSettings of the maintenance functionsWhen solvent ink is used

6 Operation for Functions6-26When sublimation transfer ink Sb51 is usedSettings of the machine setup functionsWhen solvent ink is usedWhen sublimation

6-27Invoking MACHINE SETUP functionsSettings of NCUCommon to solvent ink and sublimation transfer ink Sb51.Settings of DISPLAYCommon to solvent ink an

6 Operation for Functions6-28Invoking NCU functionsList of functionsThis section describes briefly the NCU functions and their setting values.Setting

6-29Invoking NCU functionsOutline of the NCU functionsThe NCU functions consist of operations concerning the nozzle missing detection function.Setting

6 Operation for Functions6-30NG ACTION [AFTERtheDRAWend] (*1)Set the operation of the printer after completion of printing of one file in case a prese

6-31DISPLAY settingDISPLAY settingSet a language to be used with the printer.Language Japanese English German French Spanish Italian Portuguese

1-13Warning for UsePrecautions in Use CAUTIONPower supply Do not turn OFF the main power switch on the side face.Heater Do not spill liquid on the p

6 Operation for Functions6-32Applied settings of functionsInitial settings can be changed, as required.Settings of heatersSetting items for heatersThe

6-33Applied settings of functionsDetailed settings of heatersMake settings of the pre-heater, print-heater and post-heater built in the platen.The tem

6 Operation for Functions6-34Setting the temperatures and standby time of heatersSet the temperatures and standby time of heaters by the following pro

6-35How to operate function menusHow to operate function menusThe following pages show the operating procedures and the messages displayed on the LCDs

6 Operation for Functions6-36Functions related to the cutterWhen the media is to be cut at a desired positionCut the media at any desired position wit

6-37Functions related to print qualityFunctions related to print qualityWith function menus of the printer, the print quality can be checked and setti

6 Operation for Functions6-38Functions related to inkWhen ink sets (4-color and 6-color) are to be changedMAINTENANCE <ENT>ST.MAINTENANCE <e

6-39Functions related to inkWhen ink sets (4-color and 6-color) are to be changed (continued)Set all ES3 INKcartridges.ES3-4ColorMMCC YYKK KKYY CC

6 Operation for Functions6-40Function Flowchart [BOOT]JV5-320S(S)JV5-320S(A)HS Sol, Eco-HS1 (Solvent ink)Sb51 (Water-based ink)

6-41Function Flowchart [BOOT]

1 Safety Precautions1-14CAUTIONS and NOTES CAUTIONS and NOTESHandling of ink cartridges Use the JV5 genuine ink. Remember that the user shall be char

6 Operation for Functions6-42Function Flowchart [LOCAL mode]

6-43Function Flowchart [LOCAL mode](S)

6 Operation for Functions6-44

6-45Function Flowchart [LOCAL mode]

6 Operation for Functions6-46Function Flowchart [REMOTE mode]

6-47Function Flowchart [REMOTE mode]

6 Operation for Functions6-48Function Flowchart [FUNCTION Key]

6-49Function Flowchart [FUNCTION Key]

6 Operation for Functions6-50When solvent ink is used. When sublimation transfer ink Sb51 is used.LEFT:ONx1 RIGHT:ON(OFF, ONx1 to ONx5) (OFF

6-51Function Flowchart [FUNCTION Key]

1-15Warning for UseNotes on maintenance It is strongly recommended to use the printer in a room that is not dusty. Set the Refresh level 2 or 3 when

6 Operation for Functions6-52DECIDE = [ENTER]TIMER SET = [FUNC.]

6-53Function Flowchart [FUNCTION Key]INPUT RANGE0 - 60min, CONTINUE[1] VACUUMSTOP TIMER :0min 0 to 60min/CONTINUE

6 Operation for Functions6-54

6-55Function Flowchart [FUNCTION Key]

6 Operation for Functions6-56

6-57Function Flowchart [FUNCTION Key]

6 Operation for Functions6-58

6-59Function Flowchart [FUNCTION Key]

6 Operation for Functions6-60

6-61Function Flowchart [FUNCTION Key]

1 Safety Precautions1-16Types of media that can be usedThe types of media that can be used with the printer are roll media and cut sheet media.The typ

6 Operation for Functions6-62

6-63Function Flowchart [FUNCTION Key]

6 Operation for Functions6-64

6-65Function Flowchart [FUNCTION Key]

6 Operation for Functions6-66

6-67Function Flowchart [FUNCTION Key]

6 Operation for Functions6-68:FORE&BACKPRE-FEED METHODSELECT:FORE&BACK10 to 1000FORE-> BACK-> FORE:ONMACHINE SETUPPRE-FEED METHOD<ent

6-69Function Flowchart [FUNCTION Key]

6 Operation for Functions6-70MEDIAMEDIA DETECTThicknessDETECT<ent>MEDIA DETECTFEED ERR. DETECT<ent>FEED ERR. DETECTSETUP :ON OF

6-71Function Flowchart [FUNCTION Key]

1-17Warning labelsWarning labelsWarning labels are stuck on the printer body. Be sure to fully understand the warning given on the labels. If a warnin

6 Operation for Functions6-72

6-73Function Flowchart [FUNCTION Key]

6 Operation for Functions6-74

6-75Function Flowchart [FUNCTION Key]

6 Operation for Functions6-76

6-77Function Flowchart [FUNCTION Key]

6 Operation for Functions6-78D201703-14-18042008

Printed in Japan© MIMAKI ENGINEERING CO., LTD.FW:3.00EM

CAUTIONDISCLAIMER OF WARRANTYTHIS LIMITED WARRANTY OF MIMAKI SHALL BE THE SOLE AND EXCLUSIVEWARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS O

1 Safety Precautions1-18Rear(Reorder: No.903239)(Reorder: No.903968)(Reorder: No.904130)(Reorder: No.903404)(Reorder: No.905393)(Reorder: No.905392)

1-19Basic specificationsBasic specificationsItem SpecificationPrint head Method Drop-on-demand piezoelectric print headsSpecification 4-heads Staggerd

1 Safety Precautions1-20*1 Without deflection of the roll when it is retained at both ends.*2 Main unit and heaterCutting of media Cutting of Y direct

1-21Basic specificationsSpecifications for inkTo use Eco-HS1 ink with a good image quality Head gap (the length between media and head nozzle) is rec

1 Safety Precautions1-22Notes on USB 2.0 InterfaceWhen two or more JV5 printers are connected to one personal computerWhen two or more JV5 printers ar

1-23Basic specificationsNotes on data output from USB memoryWhen spool data stored on USB memory is to be output for printing, the data is transferred

1 Safety Precautions1-24

Configurations and Functions ...2-2Operation Panel ...

2 Before Use2-2Configurations and FunctionsFront11112313414515616717818920, 21102221923

2-3Configurations and FunctionsName Function1Ink station Set the specified ink cartridges in the ink station.2Ink cartridges Each cartridge contains a

ii Not for use in a computer room as defined in the Standard for Protection Of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75 National D

2 Before Use2-4RearName Function1Cleaning cartridgeUse this cartridge when performing maintenance.For SOLVENT INK, use MILD SOLVENT Cleaning cartridge

2-5Configurations and FunctionsBottom (Connector)Name Function1Heavy-duty feeding device connectorConnect the heavy-duty feeding device.2Take-up devic

2 Before Use2-6Front cover and Maintenance coversOpening/closing the front cover and maintenance coversSTEPS:1 Close the front cover and maintenance c

2-7Configurations and FunctionsRelationships between ink station and head rowThe carriage mounts four heads each with eight rows of nozzles.One color

2 Before Use2-8When water-based ink is used.K BlackMMagentaBL BlueYYellowLBL Light BlueLm Light Magenta4 color ink set Four ink cartridges for each co

2-9Configurations and FunctionsCartridge controlThe printer uses two ink cartridges for each supply system (each nozzle row), i.e., 16 cartridges in t

2 Before Use2-10Relationship between warning and operationWhen switching in one supply system is impossible, the LCD panel displays the warning concer

2-11Configurations and FunctionsCarriageThe carriage is provided with the ink heads for printing, the cutter unit for cutting off the sheet of media,

2 Before Use2-12Cutter blade and cutting lineThe carriage is provided with a cutter unit for cutting off the media that has been printed on.The cutter

2-13Configurations and FunctionsPinch rollers and Feed rollersThis printer retains the media with the pinch rollers and feed rollers. During printing

iiiStructure of this Operation ManualThis manual consists of the following six chapters.TABLE OF CONTENTSShows the contents of this manual.CHAPTER 1

2 Before Use2-14HeaterThe following three heaters are built in platen.LEDs indicate the turning ON/OFF and status of the respective heaters. Turning o

2-15Configurations and Functions While the heater is on, the platen is very hot. When the front cover is to be opened or media is to be replaced, low

2 Before Use2-16Operation PanelUse the operation panel to make settings for printing or operate the printer.The operation panel is equipped with one l

2-17Operation PanelDisplayEach setting or message displayed on the LCDs is enclosed in [ ], like [TYPE 1], [PLEASE WAIT], etc. in the text of this ma

2 Before Use2-18Item / setting value indicating statusThe LCDs show the particular operation for a selected job.Display 1 :There may be a case where n

2-19Operation PanelHow to read the LED indicationsThe LEDs light up to indicate the status of the printer as described below.Heater Name Name Function

2 Before Use2-20How to use the keysThe functions of the operation panel are described below.71615141068911131242531

2-21Operation PanelFunctions of the JOG keysEach of the JOG keys varies in function according to the condition of the printer under which the key is u

2 Before Use2-22Modes and Menu ScreensModesThis printer is provided with the following four modes:NOT-READY modeThis is the mode in which the media ha

2-23About Function MenusAbout Function MenusBasic operation of a menu screenThis printer incorporates various functions, which can be operated on the

iv

2 Before Use2-24Operation to set function menusTo set a function menu, press the [FUNCTION] key in LOCAL mode and press [], [], [] or [] or [ENTER

2-25About Function Menus4 Press the [] or [] key to set ON/OFF of automatic cleaning.5 Press the [FUNCTION] key again if the setting of [CLEANING IN

2 Before Use2-26Outline of menu hierarchyFunction menuPress the [FUNCTION] key to invoke the function menu.*2 To be displayed only when the warning or

2-27About Function Menus*1 Only when dedicated sublimation transfer ink (Sb51) is used.

2 Before Use2-28Direct keysPressing direct keys will easily invoke frequently used functions.

2-29About Function MenusSetting values in function menusThe menus contain the following functions.SET UP functionsFunction name Sub function Setting v

2 Before Use2-30PRIORITY (p. 6-11)ALL HOST Sets the priority of settings (host / panel).ALL PANELINDIVIDUALLY MEDIA COMP., HEATER, PRINT MODE, INK LAY

2-31About Function MenusMAINTENANCE functionsFunction name Sub function Setting value FunctionST.MAINTE-NANCECARRIAGE OUT(Can be selected directly by

2 Before Use2-32DROP.POScorrect (p. 3-52)PATTERN 1 to 4 -40.0 to 40.0 dot Correct the difference in the ink fall points between outward trip and homew

2-33About Function MenusROUTINE SETUP ROUTINE WIP-ING (p. 4-31)SCAN COUNT 0 to 9990 times With the power turned on, the printer performs various opera

vTABLE OF CONTENTSCAUTIONFCC Statement (USA)... iiInterference to

2 Before Use2-34MACHINE SET functionsFunction name Sub function Setting value FunctionFeeding / TakeUP (p. 6-20)FEEDING ON, OFF Set whether to use or

2-35About Function MenusINFORMATION ERROR HISTORY (p. 6-23)(Can be selected directly by pressing [INFORMATION] key.)Displays the history of the errors

2 Before Use2-36NCU functionsFunction name Sub function Setting value FunctionNOZZLE CHECK (p. 6-29) ON, OFF Set whether or not to perform nozzle miss

Operation flow ...3-2Turning the power on ...

3 Printing3-2Operation flowThe following shows a series of operations and settings, ranging from power-on to end of printing.For details, refer to the

3-3Turning the power onTurning the power onTurn the power on.STEPS:1 Turn on the power to the printer.Press the power switch located on the front of t

3 Printing3-4Power SwitchesThe printer is provided with the following two power switches.Main power switch :Located on the side of the printer. Normal

3-5Adjusting the head gapAdjusting the head gapSet the head gap (height from the media to the nozzle plane of the heads).When the carriage is to move

3 Printing3-6How to check the head gapCheck the head gap by the following procedure.STEPS:1 Make sure that the printer is in LOCAL mode.If it is in RE

3-7Setting the media on the printerSetting the media on the printerThis printer can be used with roll media and cut sheet media. Use the media recomme

viCHAPTER 2Before UseConfigurations and Functions ...2-2Front...

3 Printing3-8Setting heavy-duty roll media (2.0m wide or more)Set heavy-duty roll media as following workflow. Use heavy-duty feeding / take-up devic

3-9Setting the media on the printer[1] Set a paper core on the take-up sideSet a paper core for heavy-duty roll media to the heavy-duty take-up device

3 Printing3-102 At the front, open right and left covers of heavy-duty take-up device, and take out the roll shaft.3 Remove heavy-duty roll holders on

3-11Setting the media on the printer2.Loosen lock screws (2 places) of heavy-duty roll holder on the adjuster side.3.Tighten adjust screws (2 places)

3 Printing3-12[2] Set a media to the feeding side (Back of the printer)Set a heavy-duty roll media to the heavy-duty feeding device on the back.STEPS:

3-13Setting the media on the printer3 Put the roll shaft through the paper core of the media. Heavy-duty media is normally printed on inner face. Set

3 Printing3-144 Fix heavy-duty roll holders to the media.1.Slide the paper core to the center of the roll shaft.Align the center of the paper core to

3-15Setting the media on the printer5.Tighen lock screws (2 places) to fix.5 Set the roll shaft on heavy-duty feeding device.1.Place the roll shaft on

3 Printing3-16[3] Adjust the mediaAdjust the media to start printing.STEPS:1 Open the front cover.If the front clamp lever is pushed down, push it up.

3-17Setting the media on the printer4 At the front, push the clamp lever up.5 At the front, pull out the media.From the front, taking both ends of the

viiSetting cut sheet media on the printer ...3-34Selecting and checking printing conditions ...

3 Printing3-189 With switches of the left back on the heavy-duty feeding device, adjust the tension-bar position until it becomes parallel to the floo

3-19Setting the media on the printer11Close the front cover and press the [ENTER] key.The printer performs initial operation and displays the standby

3 Printing3-2012Feed the media, and put the start of the media on the paper core with tape.1.With JOG key [] [], feed the media until the start of i

3-21Setting the media on the printer14With switches of the heavy-duty take-up device, roll up the media about once.1.Turn the left switch to MANUAL an

3 Printing3-2217Press the JOG key [] [] to lift the tension-bar up and to stretch the loosened media.Before pressing [] [] key, turn the left swit

3-23Setting the media on the printerSetting roll media (less than 2.0m wide)Set roll media as following workflow. Take care not to drop media on the

3 Printing3-24[1] Set media to the roll holder on the backSTEPS:1 Set the operation panel.1.Select [MACHINE SETUP] with [FUNCTION] key and press the [

3-25Setting the media on the printer4 At the back of the printer, position the left roll holder.1.Loosen the roll holder securing screw on the left.2.

3 Printing3-267 Pull the roll media at the back of the printer, insert it between the platen and the pinch rollers, and pull it out from the front.8 A

3-27Setting the media on the printer[2] Set media to the roll holder on the frontSTEPS:1 At the back of the printer, position the right roll holder.1.