MIMAKI JV5-160S Spezifikationen Seite 215
- Seite / 262
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
6-25
CHAPTER 6 Operation for Functions Invoking NCU functions
Invoking NCU functions
List of functions
This section describes briefly the NCU functions and their setting values.
Setting a NCU functions
The operation described below on the operation panel is required to execute NCU functions.
STEPS:
1 Make sure that the printer is in LOCAL mode, and then select [NCU] using the [FUNC-
TION] key and press the [ENTER] key.
If it is in REMOTE mode, press the [REMOTE] key once.
2 Select an NCU function and make setting.
Name Function Refer to
NOZZLE CHECK Set whether or not to perform nozzle missing detection. p. 6-26
NG ACTION (*1)
Set the operation of the printer to be performed in case the preset number of
or more missing nozzles are detected and thus NG judgment is made. (*2)
p. 6-26
NG JUDGEMENT (*1) Set the number of missing nozzles for NG judgment. (*2) p. 6-27
COND.INDICATION Displays the status of the NCU. p. 6-27
NG (*1): Bad nozzle condition.
NG (*2): One or more bad nozzles have been located on print head.
PRE PRT AFT
35°C 40°C 50°C
L. ∗ > [JV5-01]
width : ∗∗∗∗ mm
PRE PRT AFT
35°C 40°C 50°C
FUNCTION
NCU <ENT>
- OPERATION MANUAL 1
- DISCLAIMER OF WARRANTY 3
- Requests 3
- FCC Statement (USA) 4
- Foreword 5
- CHAPTER 3 Print Output 10
- CHAPTER 4 Daily Maintenance 11
- CHAPTER 5 In Case of Trouble 12
- TABLE OF CONTENTS 13
- CHAPTER 1 15
- Safety Precautions 15
- Checking the accessories 16
- Front exhaust unit Box 18
- Name QTY Remarks 19
- 1 Roll screen 160 (130) 1 19
- 4 Front exhaust unit Box 1 19
- Features 20
- Pictorial signs 23
- Notes on Installation 24
- Notes on Location 25
- Moving the printer 26
- Power Supply Connection 27
- WARNING 28
- Precautions in Use 29
- CAUTION 29
- CAUTIONS and NOTES 30
- Recommended types of media 31
- Warning labels 32
- Basic specifications 33
- *2 Main unit and heater 34
- *3 Without front exhaust unit 34
- Specifications for ink 35
- Notes on USB 2.0 Interface 36
- CHAPTER 2 39
- Basic Use of Printer 39
- Names of Parts and Functions 40
- 3 Press the [ENTER] key once 44
- Cartridge control 46
- Carriage 48
- Capping station 48
- Cutter blade and cutting line 49
- Media sensor 49
- Pinch roller 50
- Feed roller 50
- Keep the pinch rollers 50
- Clamp lever 50
- After-heater 51
- Print heater 51
- Pre-heater 51
- Operation Panel 52
- How to read the display 53
- Job processing status 54
- Message indicating status 54
- BUSY lamp 55
- HEAT SW lamp 55
- How to use the keys 56
- Functions of the JOG keys 57
- Modes and Menu Screens 58
- About Function Menus 59
- 2 Press the [FUNCTION] key 60
- Outline of menu hierarchy 62
- Direct keys 64
- SET UP functions 65
- MAINTENANCE functions 67
- MACHINE SET functions 70
- NCU functions 71
- CHAPTER 3 73
- Print Output 73
- Operation flow 74
- Turning the power on 75
- Starting up the printer 76
- Adjusting the head gap 77
- 3 Press the [END] key 78
- 2 Select a angle as setting 80
- 3 Retighten the knobs 80
- Roll holder securing screw 81
- Media support bar 82
- Rightmost pinch roller 85
- Media encoder roller 85
- Media press 85
- Media end 85
- Setting the torque limiter 89
- 3 Push down the clamp lever 91
- How to select a user type 92
- How to check the user type 93
- Operating the heaters 94
- 2 Press the [HEATER] key 95
- What is beading ? 96
- Temperature adjustment 97
- In case of heater trouble 98
- [PG DROP ADJUST.] 99
- 6 Press the [ENTER] key 100
- Abnormal pattern 101
- Normal pattern 101
- 2 Press the [CLEANING] key 102
- 5 Press the [ENTER] key 103
- 4 Press the [ENTER] key 104
- 35°C 40°C 50°C 105
- L. ∗ > [JV5-01] 105
- PRE PRT AFT 105
- Correction value: 107
- -255 ~ 255 107
- Correction value is too large 107
- OverlapClearance 107
- Correction value is too small 107
- Effective Plotting Area 110
- Establishing the Origin 111
- Printing an image 112
- 2 Press the [REMOTE] key 113
- 4 The printer start printing 113
- 2 Press the [DATA CLEAR] key 114
- 3 Press the [ENTER] key 115
- Automatic cleaning 116
- 4 Press the [FUNCTION] key 117
- [INK NEAR END] 118
- [INK END] 118
- [INK END][INK NEAR END] 119
- 2 Press the [ENTER] key 120
- Turning the power off 121
- CHAPTER 4 123
- Daily Maintenance 123
- Routine Maintenance 124
- Notes on cleaning solution 125
- Cleaning exterior surfaces 125
- Cleaning the platen 125
- Cleaning the media sensor 126
- Cleaning the media press 126
- Opening a maintenance cover 127
- ST.MAINTENANCE 131
- COMPLETED :end 131
- ∗Being Initialized∗ 131
- NOT POW-OFF !! 131
- PLEASE WAIT 131
- 7 Press the [ENTER] key 134
- 11Press the [ENTER] key 134
- To step 5 To step 10 142
- PUMP tube cleaning 144
- Wiper cleaning 146
- [CR.MAINTENANCE] 149
- Never rub the nozzle part 150
- Media sensor at the heads 151
- Input range: OFF, 1 to 168 153
- Other maintenance functions 161
- FULL, or NONE 163
- 3 Open the front cover 167
- Install the new cutter unit 168
- CHAPTER 5 169
- In Case of Trouble 169
- Power does not turn on 170
- Check the basic operation 171
- If image quality is poor 172
- (jet deviation) 173
- [DISCHARGE&WASH] 174
- 4 Remove the ink cartridges 175
- Ink cartridge trouble 179
- [ERROR HISTORY] is displayed 181
- Warning messages 182
- Error messages 185
- CHAPTER 6 191
- Operation for Functions 191
- Invoking SET UP functions 193
- Set the printing conditions 194
- (See 3-34) 195
- (See 6-29) 195
- PRINT MODE 196
- INK LAYERS 198
- DRYING TIME 198
- AUTO CUT 199
- PRE-FEED 199
- COLOR PATTERN 199
- (See 3-44) 200
- (See 3-5) 201
- List of functions 202
- 2 Press the [ST.MAINT] key 203
- RESIDUAL] 204
- Setting a MACHINE SETUP 208
- DRYNESS FEED 209
- CONFIRM. FEED 209
- TIME SET 209
- DEODORIZE FAN 209
- UNIT SETUP 210
- STAMP SETUP 210
- MACHINE NAME 211
- INFORMATION 212
- ERROR HISTORY 212
- MAINTE. HISTORY 212
- PRT.modeHISTORY 212
- Serial&DealerNo 214
- Invoking NCU functions 215
- Outline of the NCU functions 216
- NG JUDGEMENT (*1) 217
- COND.INDICATION 217
- DISPLAY setting 218
- Applied settings of functions 219
- Detailed settings of heaters 220
- How to operate function menus 223
- Change is 225
- Functions related to ink 226
- Remove the cleaning 227
- Function Flowchart [BOOT] 228
- To p.6-42 230
- From p.6-40 232
- To p.6-48 236
- To p.6-50 238
- From p.6-46 238
- From p.6-48 240
- To p.6-54 242
- From p.6-52 244
- To p.6-56 244
- From p.6-54 246
- To p.6-58 To p.6-58 246
- To p.6-60 248
- From p.6-56 From p.6-56 248
- From p.6-58 250
- To p.6-64 252
- From p.6-62 254
- To p.6-68 256
- From p.6-66 258
- D201515-1.00-11082006 260
- Printed in Japan 262
Verwandte Produkte und Handbücher für Drucken & Scannen MIMAKI JV5-160S
(146 Seiten)
Drucken & Scannen MIMAKI Tx2-1600 Bedienerhandbuch
(170 Seiten)
(170 Seiten)
Drucken & Scannen MIMAKI TS5-1600AMF Spezifikationen
(288 Seiten)
(288 Seiten)
(288 Seiten)
Drucken & Scannen MIMAKI UJF-3042FX Spezifikationen
(138 Seiten)
(138 Seiten)
Drucken & Scannen MIMAKI GP-1810 Bedienerhandbuch
(152 Seiten)
(152 Seiten)
Drucken & Scannen MIMAKI JF-1631 Spezifikationen
(142 Seiten)
(142 Seiten)
Drucken & Scannen MIMAKI UJF-3042HG Spezifikationen
(156 Seiten)
(156 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern